Plumbing 101: A Guide to Bathtub Installation
Plumbing 101: A Guide to Bathtub Installation
Blog Article
We've encountered this great article relating to A Step-by-Step Guide to Installing a Bathtub directly below on the internet and think it made sense to discuss it with you here.
Mounting a tub isn't exactly brain surgery, yet it does call for strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old bathtub with a new one is also a moderately difficult project. If the old bathtub is conveniently obtainable, the task can relocate easily; if you need to open a wall to remove the old bathtub as well as position the new tub, the task is much harder. In either situation, the task is within a house handyman's skills, although you will certainly require a helper to vacate the old tub and embeded in the new one. Make sure you have actually qualified on your own for the task and also are comfortable attempting it. As opposed to working with a contractor to take control of a halfway-completed task, it is far better to think about employing one before you start. Possibilities are you may require a specialist plumber to make tube connections.
This post will certainly assist you mount a new tub in your restroom if you have actually currently purchased a brand-new bathtub and also don't need to alter the setup of your previous water supply pipes.
Your tools as well as product list need to comprise the following:
Planning for the Installment
To start with, the sustaining structure provided with the bathroom ought to be fitted (if needed) according to the producer's instructions. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is important to see to it that if the faucet comes with a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the faucets system to prevent pressure on the bathtub.
Fit the adaptable faucet adapters to the bottom of the two faucets making use of 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make certain you utilize all of the supplied washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath must currently prepare to be fitted in its final position.
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, after that the first thing you need to do is detach the water. After doing so, switch on the faucets to drain any water remaining in the system. The procedure of eliminating the existing taps can be fairly troublesome due to the limited accessibility that is usually the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a cloth ready for the staying water that will certainly originate from the pipes. As soon as the supply pipelines have actually been removed, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the single faucets from transforming throughout this procedure. Once the taps have been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing substance.
Before going on to fit the brand-new taps, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the new taps, then a shank adapter is needed for the new taps to fit.
Installing the Tub
Using both wood boards under its feet, position the bath tub in the required setting. The wooden boards are practical in uniformly spreading out the weight of the tub over the area of the boards instead of focusing all the weight onto 4 little points.
The next goal is to make sure that the bath tub is leveled all round. This can be accomplished by inspecting the level as well as changing the feet on the tub up until the spirit level reads level.
To mount faucets, fit the bottom of the furthest adaptable faucet port to the suitable supply pipeline by making a compression sign up with; then do the very same for the various other tap.
Activate the water as well as check all joints and also new pipework for leakages as well as tighten them if necessary. Load the tub and likewise check the overflow electrical outlet and the regular electrical outlet for leaks.
Lastly, fix the bath paneling as defined in the manufacturer's user's manual. Tiling and also sealing around the tub must wait until the bathtub has been used a minimum of when as this will certainly resolve it right into its last setting.
Suitable New Touches
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the other end gives a link to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly need reducing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, place the faucet in the mounting hole in the bath/basin making certain that the washing machines are in area in between the tap and also the sink. Protect the tap in position with the producer provided backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The former kind should be linked to the faucet ends first, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bathroom satisfies the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to fracture an inflexible seal, causing the water to penetrate the wall between the bath and the tiling, resulting in problems with moisture as well as possible leaks to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your components and also fittings. They are sold in tubes and cartridges, as well as are capable of securing voids up to a size of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to always load the tub with water prior to sealing, to permit the motion experienced when the bathtub is in usage. The sealant can fracture relatively very early if you do not take into consideration this movement before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise conveniently available on the market. It is a good idea to fit the floor tiles using water-resistant or water resistant adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am very curious about Tools You Need to Install a New Bathtub and I really hope you liked the entire entry. Enjoyed our post? Please share it. Let others discover it. I treasure reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Get Quote Report this page